Heltec Automation Docs
latest

Language

  • 简体中文

LORA GATEWAY

  • Contents
  • SX130x Module
  • HT-M00 Dual Channel LoRa Gateway
  • HT-M01 Evaluation LoRa Gateway
  • HT-M01S Indoor LoRa Gateway
  • HT-M01S (Rev. 2.0)
  • HT-M02 Edge LoRa Gateway(4G/LTE)
  • HT-M02 Edge LoRa Gateway(POE)
  • Frequently Asked Questions

CubeCell

  • Contents
  • Quick Start
  • LoRaWAN
  • AT Command List
  • CubeCell Dev-Board
  • CubeCell Capsule Seneor
  • CubeCell Module
  • Frequently Asked Questions

ESP32 + LoRa

  • Contents
  • Quick Start
  • LoRaWAN
  • Maximum Distance Test
  • WiFi LoRa 32
  • Wireless Stick
  • Wireless Stick Lite
  • Wireless Shell
  • Wireless Bridge
  • Frequently Asked Questions

STM32 + LoRa

  • Contents
    • Quick Start
    • LoRaWAN
    • LoRa Node 151
    • Turtle Board
    • Frequently Asked Questions
  • Quick Start
  • LoRaWAN
  • LoRa Node 151
  • Turtle Board
  • Frequently Asked Questions

ESP32 + Arduino

  • Contents
  • Quick Start
  • WiFi kit 32
  • Frequently Asked Questions

ESP8266 + Arduino

  • Contents
  • Quick Start
  • WiFi Kit 8
  • Frequently Asked Questions

General Docs

  • Contents
  • How to Install Git and Arduino
  • Establish Serial Connection
  • LoRaWAN Example Sub-Band Usage
  • LoRaWAN Frequency Plans
  • LoRaWAN Frequency Plans and Regulations by Country
  • Subscribe MQTT Messages
  • Publish MQTT Message
  • Decode LoRaWAN payload
  • How To Config Rasberry Pi
  • Get Limited Technical Resources
  • Connect to Single_channel Gateway
  • Heltec LoRaWAN Test Server Login Issue
Heltec Automation Docs
  • »
  • Contents
  • Edit on GitHub

Contents

简体中文

This document branch is for Heltec STM32 + LoRa Node series.

STM32 is a powerfull SoC with Ultra-low-power 32-bit MCU,The benefit of “STM32 + LoRa” combination:

  • Low power features;

  • Multiple bus interfaces;

  • Powerful computing skills;

  • Power mananagement system and different types of batteries support;

  • Multiple general GPIOs;

  • LoRaWAN 1.0.2 protocol support.

Tip

This series boards also don’t have an onboard USB-UART bridge. If plug it directly into a computer, it may prompt “Unrecognized USB device”, which is normal.

  • Quick Start
    • Install STM32CubeIDE
    • Install STM32CubeProgrammer
  • LoRaWAN
    • Get LoRaWAN Example Code
      • Get Chip ID
      • Get LoRaWAN Example Code
    • Configuration Parameters
      • Summary
      • Preparation
      • Config steps
    • Connect to LoRaWAN server
      • Connect to TTN
        • Register a device
      • Connect to ChirpStack
      • Connect to HelTec server
        • Register a device
      • Important Hints
  • LoRa Node 151
    • Download Firmware
      • Via DFU Mode
      • Via ST-LINK
    • Establish Serial Connection
      • Use UART
      • Use virtual serial port
    • Pingpong Test
      • Prepare
      • Start test
    • Hardware Update Logs
      • V1
      • V2.0
      • V2.2
    • Relevant Offical Resources
  • Turtle Board
    • Download Firmware
      • Via DFU Mode
      • Via ST-LINK
    • Establish Serial Connection
      • Use UART
      • Use virtual serial port
    • RadioShuttle Protocol Resource
      • The RadioShuttle Wireless Protocol
      • RadioShuttle STM32 Utility
    • Hardware Update Logs
      • V1.1
    • Relevant Offical Resources
  • Frequently Asked Questions
    • Can’t Download Firmware
    • Serial port has no output
Previous Next

© Copyright 2019, Heltec. Revision fab7a4df.

Built with Sphinx using a theme provided by Read the Docs.
Read the Docs v: latest
Versions
latest
Downloads
pdf
html
epub
On Read the Docs
Project Home
Builds